FIRST 60 SECONDS
Signal is missing. Where is it?
Mute → fader → gain → source → cable → patch → amp. Stop at the first stage that fails.
1 · Mute / soloclear
2 · Fader / gainup
3 · Sourceknown good
4 · Ampon / protect
PROCEDURE 01
No sound
Anything is silent. Work in this order and change one thing at a time.
- Mutes and solos: channel, bus, master, monitor, DCA / mute group.
- Fader, then channel gain, then output patch.
- What changed in the last ten minutes?
- Known-good mic and cable into the same input. If that works, the source is the problem.
- 48 V for condensers, pad off, DI battery alive.
- Console routing: input patch, bus assign, output patch, crosspoints.
- Amp or processor: power, protect LED, preset, input attenuator.
- Dante: one clock leader, matching sample rate, subscription active.
- Bypass the console: mic straight into an amp. If that makes sound, stop pulling cables.
- Still nothing? Check the wall circuit and that the speaker is on mains.
PROCEDURE 02
Feedback
A wedge or the PA is ringing. Cut, do not boost.
- Find the frequency on the RTA. Write it down.
- Narrow cut, Q 6-12, 3-6 dB. More than 6 dB means the problem is gain-before-feedback.
- Graphic on the wedge, parametric on the channel. Not both on the same band.
- High-pass everything that does not need low end: vocal 80-120 Hz, wedge 100 Hz.
- Ring out at show level, then back off 3 dB.
- Move the mic or the speaker into the mic's null before adding more EQ.
- Look for a second path: two wedges into one mic, or the vocal mic hearing FOH.
- If you cannot cut it because the source lives there, reduce level or move something.
PROCEDURE 03
RF dropout
Wireless is silent, noisy, or dropping. Different faults, different fixes.
- Dropout (silence or a click) or interference (hash, someone else's audio)?
- Batteries: measure under load, replace at half capacity, note the time.
- Antennas in line of sight, above the crowd, away from LED walls and switching PSUs.
- Scan in the room at show time, not at load-in.
- Coordinate in WWB / WSM: exclude TV channels, keep spacing where you can.
- Squelch just above the noise floor. Too high drops out at range; too low hisses.
- Same group and bank, same pack power, pilot tone on, controls locked.
- Check receive level, not just RF bars — a quiet pack sounds like a dropout.
- Spare pack per performer, spare receiver if possible, wired mic as the last resort.
PROCEDURE 04
Dante / network
Devices missing, red subscriptions, clicks, or silence.
- Exactly one preferred clock leader. Two means clicks or silence.
- Same sample rate everywhere. 48 kHz is the safe default.
- A red or grey subscription is a clock, rate or firmware problem, not routing.
- Latency 1 ms at FOH, 2-5 ms across a large network. Changing it forces re-subscribe.
- Primary and secondary on separate switches; never loop both into one unmanaged switch.
- Static addressing: write the plan down before plugging in.
- No DHCP means 169.254.x.x — either give the network DHCP or set statics deliberately.
- Greyed-out device: wrong subnet, duplicate IP, other VLAN, or secondary-only.
- Managed switches need IGMP snooping and a querier for multicast.
- Verify with a 1 kHz tone from 04_TEST-SIGNALS, not just green ticks.
PROCEDURE 05
Session start
The first twenty minutes of any studio session.
- Sample rate and clock decided before anything is recorded.
- Correct interface in the DAW, not “system default”.
- Every input labelled, in the same order as the input list.
- Gain for -18 dBFS average, peaks -10 to -6, never touching 0.
- Headphone mixes confirmed with the artist; talkback working.
- Record ten seconds, play it back through the monitors.
- File naming and folder set before the first take.
- Backup location configured and tested.
- Delivery spec confirmed: rate, depth, format, loudness, naming.
- Notes: tempo, tuning, mic positions, preamps, plugin chain.
PROCEDURE 06
Recording failsafe
The take you cannot play back is not a take.
- Free space: 8.6 MB per minute per track at 48/24. Sixteen tracks for three hours is about 25 GB.
- Record to an internal or external SSD. Never a thumb drive or a network share.
- Disk write test: five minutes of silence, confirm no dropouts.
- Auto-save on, backup copy enabled.
- Watch record meters and CPU, not the artist.
- At every break, copy the project to the second location.
- Glitch: stop, save as a new name, restart the interface, re-test.
- After: play the last 30 seconds of every take and check file counts.
PROCEDURE 07
Gain & hum
Distortion, hiss, buzz, or a ground loop.
- Set analogue gain so the loudest source peaks near -18 to -12 dBFS.
- One gain stage at a time: preamp, processor, console, amp. Unity where possible.
- Know which meter scale the desk uses. 0 on the meter is not 0 dBFS.
- Hum: unplug the source. If it stays, it is the system, not the source.
- Same circuit for FOH, stage and amps where possible.
- Ground loop: transformer isolation or a proper split. Never lift the mains earth.
- 50/60 Hz exactly is mains. Broad hash is a switching supply or a data cable.
- 48 V into a ribbon mic is a repair bill. Check before pressing the button.
PROCEDURE 08
System tuning
Measuring and aligning a PA, fast and repeatably.
- Measurement mic at ear height at the listening position, cal file loaded.
- Pink noise at show level. Do not EQ at 60 dBA for a 95 dBA show.
- Left, right, then both. Fix one speaker before the pair.
- Delay first: subs to tops, then delays to mains. Re-measure before EQ.
- Cuts only, wide and shallow: 3-6 dB, Q 0.7-2. Narrow only for real resonances.
- Do not EQ a bad speaker position. Move the speaker or the seat.
- Verify at two positions. A curve that works at one seat is a comb filter.
- Listen to a reference track. If it measures flat and sounds wrong, trust the track.
- Save the measurement and the preset with venue and date in the name.