Field guide · eight procedures

Emergency handbook

Print · A4 · 8 procedures
These are decision lists, not tutorials. They assume you know the gear and need the order of operations. Change one thing at a time and say it out loud. The long versions are in Emergency_Checklists/.
FIRST 60 SECONDS

Signal is missing. Where is it?

Mute → fader → gain → source → cable → patch → amp. Stop at the first stage that fails.

1 · Mute / soloclear
2 · Fader / gainup
3 · Sourceknown good
4 · Ampon / protect
PROCEDURE 01

No sound

Anything is silent. Work in this order and change one thing at a time.

  1. Mutes and solos: channel, bus, master, monitor, DCA / mute group.
  2. Fader, then channel gain, then output patch.
  3. What changed in the last ten minutes?
  4. Known-good mic and cable into the same input. If that works, the source is the problem.
  5. 48 V for condensers, pad off, DI battery alive.
  6. Console routing: input patch, bus assign, output patch, crosspoints.
  7. Amp or processor: power, protect LED, preset, input attenuator.
  8. Dante: one clock leader, matching sample rate, subscription active.
  9. Bypass the console: mic straight into an amp. If that makes sound, stop pulling cables.
  10. Still nothing? Check the wall circuit and that the speaker is on mains.
PROCEDURE 02

Feedback

A wedge or the PA is ringing. Cut, do not boost.

  1. Find the frequency on the RTA. Write it down.
  2. Narrow cut, Q 6-12, 3-6 dB. More than 6 dB means the problem is gain-before-feedback.
  3. Graphic on the wedge, parametric on the channel. Not both on the same band.
  4. High-pass everything that does not need low end: vocal 80-120 Hz, wedge 100 Hz.
  5. Ring out at show level, then back off 3 dB.
  6. Move the mic or the speaker into the mic's null before adding more EQ.
  7. Look for a second path: two wedges into one mic, or the vocal mic hearing FOH.
  8. If you cannot cut it because the source lives there, reduce level or move something.
PROCEDURE 03

RF dropout

Wireless is silent, noisy, or dropping. Different faults, different fixes.

  1. Dropout (silence or a click) or interference (hash, someone else's audio)?
  2. Batteries: measure under load, replace at half capacity, note the time.
  3. Antennas in line of sight, above the crowd, away from LED walls and switching PSUs.
  4. Scan in the room at show time, not at load-in.
  5. Coordinate in WWB / WSM: exclude TV channels, keep spacing where you can.
  6. Squelch just above the noise floor. Too high drops out at range; too low hisses.
  7. Same group and bank, same pack power, pilot tone on, controls locked.
  8. Check receive level, not just RF bars — a quiet pack sounds like a dropout.
  9. Spare pack per performer, spare receiver if possible, wired mic as the last resort.
PROCEDURE 04

Dante / network

Devices missing, red subscriptions, clicks, or silence.

  1. Exactly one preferred clock leader. Two means clicks or silence.
  2. Same sample rate everywhere. 48 kHz is the safe default.
  3. A red or grey subscription is a clock, rate or firmware problem, not routing.
  4. Latency 1 ms at FOH, 2-5 ms across a large network. Changing it forces re-subscribe.
  5. Primary and secondary on separate switches; never loop both into one unmanaged switch.
  6. Static addressing: write the plan down before plugging in.
  7. No DHCP means 169.254.x.x — either give the network DHCP or set statics deliberately.
  8. Greyed-out device: wrong subnet, duplicate IP, other VLAN, or secondary-only.
  9. Managed switches need IGMP snooping and a querier for multicast.
  10. Verify with a 1 kHz tone from 04_TEST-SIGNALS, not just green ticks.
PROCEDURE 05

Session start

The first twenty minutes of any studio session.

  1. Sample rate and clock decided before anything is recorded.
  2. Correct interface in the DAW, not “system default”.
  3. Every input labelled, in the same order as the input list.
  4. Gain for -18 dBFS average, peaks -10 to -6, never touching 0.
  5. Headphone mixes confirmed with the artist; talkback working.
  6. Record ten seconds, play it back through the monitors.
  7. File naming and folder set before the first take.
  8. Backup location configured and tested.
  9. Delivery spec confirmed: rate, depth, format, loudness, naming.
  10. Notes: tempo, tuning, mic positions, preamps, plugin chain.
PROCEDURE 06

Recording failsafe

The take you cannot play back is not a take.

  1. Free space: 8.6 MB per minute per track at 48/24. Sixteen tracks for three hours is about 25 GB.
  2. Record to an internal or external SSD. Never a thumb drive or a network share.
  3. Disk write test: five minutes of silence, confirm no dropouts.
  4. Auto-save on, backup copy enabled.
  5. Watch record meters and CPU, not the artist.
  6. At every break, copy the project to the second location.
  7. Glitch: stop, save as a new name, restart the interface, re-test.
  8. After: play the last 30 seconds of every take and check file counts.
PROCEDURE 07

Gain & hum

Distortion, hiss, buzz, or a ground loop.

  1. Set analogue gain so the loudest source peaks near -18 to -12 dBFS.
  2. One gain stage at a time: preamp, processor, console, amp. Unity where possible.
  3. Know which meter scale the desk uses. 0 on the meter is not 0 dBFS.
  4. Hum: unplug the source. If it stays, it is the system, not the source.
  5. Same circuit for FOH, stage and amps where possible.
  6. Ground loop: transformer isolation or a proper split. Never lift the mains earth.
  7. 50/60 Hz exactly is mains. Broad hash is a switching supply or a data cable.
  8. 48 V into a ribbon mic is a repair bill. Check before pressing the button.
PROCEDURE 08

System tuning

Measuring and aligning a PA, fast and repeatably.

  1. Measurement mic at ear height at the listening position, cal file loaded.
  2. Pink noise at show level. Do not EQ at 60 dBA for a 95 dBA show.
  3. Left, right, then both. Fix one speaker before the pair.
  4. Delay first: subs to tops, then delays to mains. Re-measure before EQ.
  5. Cuts only, wide and shallow: 3-6 dB, Q 0.7-2. Narrow only for real resonances.
  6. Do not EQ a bad speaker position. Move the speaker or the seat.
  7. Verify at two positions. A curve that works at one seat is a comb filter.
  8. Listen to a reference track. If it measures flat and sounds wrong, trust the track.
  9. Save the measurement and the preset with venue and date in the name.